BWYRX - FLOOR & DECK ENAMEL, 80 LINE
- MSDS: BWYRX
- Manufacturer: SINCLAIR PAINT CO
- Product Name: FLOOR & DECK ENAMEL, 80 LINE
- National Stock Number: 8010-00N057114
Product Identification
Product ID:FLOOR & DECK ENAMEL, 80 LINE
MSDS Date:09/23/1988
FSC:8010
NIIN:00N057114
MSDS Number: BWYRX
Responsible Party
LOS ANGELES, CA 90040
US
Emergency Phone: 213-664-2121
Info Phone: 213-888-8888
Cage: 0U0K0
Contractor
Telephone: 213-888-8888
Cage: 0U0K0
Ingredients
5
CAS: 8052-41-3
RTECS: WJ8925000
OSHA PEL 500 PPM
ACGIH TLV: 100 PPM
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:MAY CAUSE EYE, NOSE, THROAT/SKIN
IRRIT. MAY CAUSE HDCH, NAUS, DIZZ, LASSITUDE/LOSS OF
COORD/CONSCIOUSNESS. CHRONIC:THIS PROD CNTNS CRYSTALLINE SILICA
(CHEM NAME FOR BEACH SAND) THAT IS FULLY ENC APSULATED. CRYSTALLINE
SILICA HAS BEEN LISTED BY IARC AS HAVING LIMITED EVIDENCE AS A
HUMAN CARCIN BY (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZS:INHALATION.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INHALATION:REMOVE TO FRESH AIR, GIVE ARTIFICIAL RESPIRATION
IF BREATHING HAS STOPPED. EYES:FLUSH WITH FRESH WATER FOR AT LEAST
15 MINUTES. SKIN:WASH WITH SOAP AND WATER. CHANGE CONTAMINATED
CLOTHING. INGESTION:DO NOT INDUCE VOMITING. KEEP HEAD LOWER THAN
WAIST. ASPIRATION OF VOMITUS MAY CAUSE CHEMICAL PNEUMONITIS. CALL A
PHYSICIAN.
Fire Fighting
Flash Point:105F,41C
Lower Limits:SEE INGS
Extinguishing Media:FOAM, DRY CHEMICAL OR CO*2
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER MAY BE UNSUITABLE AS AN EXTING MEDIUM, BUT HELPFUL IN
COOLING HOT SURFS & UNRUPTURED CNTNRS.(SUPDAT)
Unusual Fire/Explosion Hazard:VAPS ARE HVR/AIR & MAY ACCUM IN LOW AREAS
OF POOR VENT/TRAVEL ALONG GROUND TO REMOTE IGNIT SITES. CLSD CNTNRS
CAN BUILD UP PRESS & MAY EXPLODE WHEN (SUPP DATA)
Accidental Release
Spill Release Procedures:REMOVE SOURCES OF HEAT, SPARK OR FLAME. WEAR
APPROPRIATE CLOTHING AND GEAR. CLEAN UP SPILLS IMMEDIATELY WITH
ABSORBENTS SUCH AS CLAY, SAND OR OTHER SUITABLE MATERIALS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:KEEP COOL, DRY AND AWAY FROM HEAT,
SPARK OR FLAME (ALL IGNITION SOURCES). STORE IN A WELL VENTILATED
AREA. KEEP CONTAINERS UPRIGHT WHEN NOT IN USE.
Other Precautions:AVOID EXCESSIVE PERSONAL EXPOSURE. GROUND AND BOND
ALL TRANSFER CONTAINERS AND EQUIPMENT. DO NOT WELD, DRILL, CUT OR
GRIND FULL, PARTIAL, OR EVEN EMPTY CONTAINERS (RESIDUE AND/OR
VAPORS MAY BE PRESENT ). USE WITH ADEQUATE VENTILATION.
Exposure Controls
Respiratory Protection:AVOID EXCESSIVE VAPOR INHALATION. IF PEL OR TLV
IS EXCEEDED, USE A NIOSH/MSHA APPROVED RESPIRATOR OR SCBA. USE A
NIOSH/MSHA APPROVED MECHANICAL FILTER TO REMOVE SOLID AIRBORNE
PARTICLES DURING SPRAY A PPLICATION.
Ventilation:GEN MECH VENT MAY PROVIDE SUFFICIENT VOL & PATTERN AIR
MOVEMENT TO KEEP EXPOS BELOW PEL & TLV. EXPLO-PROOF VENT (SUPDAT)
Protective Gloves:NEOPRENE GLOVES, AS NEEDED.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASHES AND SAFETY SHOWERS AS NEEDED.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRE FIGHT PROC:IF WATER MUST BE USED, USE WATER FOG (NOT DIRECT STREAM
OF WATER) AS BURNING MATERIAL MAY SPREAD AND/OR FLOAT ON WATER
SURFACE. EXPLO HAZS:EXPOSED TO EXTREME HEAT. VENT:IS RECOMMENDED
FOR FLAMMABLE MATERIALS.
Chemical Properties
Boiling Pt:B.P. Text:>300F,>149C
Vapor Pres:SEE INGS
Vapor Density:HVR/AIR
Spec Gravity:1.16-1.21
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:53-55
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG ACIDS AND BASES, SELECTED AMINES.
Stability Condition to Avoid:HEAT, SPARKS OR FLAME.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
UNIDENTIFIED ORGANIC COMPOUNDS.
Disposal
Waste Disposal Methods:PLACE IN NON-LEAKING CONTAINERS AND DISPOSE OF
IN ACCORDANCE WITH APPLICABLE LOCAL, COUNTY, STATE AND FEDERAL
REGULATIONS. BEFORE BEGINNING CLEAN-UP, REFER TO ALL SECTIONS OF
THIS MSDS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.